International Conference on Gears 2023:

VDI Wissensforum GmbH

doi:10.51202/9783181024225

Zusammenfassung

Foreword The International Conference on Gears in Garching near Munich, Germany, is an established platform for researchers on and manufacturers of gears and transmission systems. At the 10th issue of the conference in September of 2023, gear experts discussed the latest developments and research results from the powertrain industry and academia. Given the increasing challenges of climate change and its impacts, acting in compliance with the UN Sustainable Development Goals is mandatory for all engineers today. Gear engineers must consider these objectives in their research and development activities and provide solutions that meet the technical requirements and contribute to achieving the UN goals. Greenhouse gas (GHG) emission is a primary driver for climate change. Reducing GHG emissions should be an urgent action for the combat against climate change. Therefore, the research on efficiency is assigned a key role. Several contributions in this report discuss the possibilities for further improvement in efficiency from different points of view, like gear design or lubrication. Other subjects of the conferences are Responsible Consumption and Production. H...

Schlagworte

Publikation durchsuchen

Bibliographische Angaben

Copyrightjahr: 2023
ISBN-Print: 978-3-18-092422-9
ISBN-Online: 978-3-18-102422-5
Verlag: VDI Verlag, Düsseldorf
Reihe: VDI-Berichte
Band: 2422
Sprache: Deutsch
Seiten: XXIX
Produkttyp: Sammelband

Inhaltsverzeichnis

KapitelSeiten

Titelei/Inhaltsverzeichnis Kein Zugriff
Foreword Kein Zugriff
1. Reuse Kein Zugriff D. Krüger
2. Efficiency-improvement with low-loss-gears by two different application Kein Zugriff B.-R. Höhn, Y. Zhang, M. Geitner, M. Otto
1. Optimised statistical evaluation for the determination of tooth root endurance strength Kein Zugriff A. Alnahlaui, P. Tenberge
2. The consequences of different methodologies for the elaboration of pulsator test results with respect to the load spectrum assessment of gears Kein Zugriff L. Bonaiti, M. Monti, C. Gorla, M. Geitner, T. Tobie, K. Stahl
3. Tooth Bending Strain Rate Analysis in a Counter Shaft Drivetrain and Implications on Fatigue Strength Kein Zugriff I. Hong, D. Talbot
1. Investigation of the electrical behavior of a spur gear stage pair by means of impedance measurements Kein Zugriff M. Werner, S. Graf, M. Oehler, O. Koch
2. Measuring Instantaneous Angular Speed using a Gear Wheel as Material Measure to detect Pitting Damage during an Endurance Test Kein Zugriff Y. Koch, E. Kirchner, J. Hirschmann
3. Pitting Detection for Prognostics and Health Management in Gearbox Applications Kein Zugriff L. Binanzer, L. Merkle, M. Dazer, A. Nicola
1. Crack growth based tooth root life prediction model – an influence quantity analysis Kein Zugriff J. Lövenich, M. Zalfen, D. Mevissen, J. Brimmers, C. Brecher
2. Experimental Investigation of the load carrying capacity of beveloid gears with optimized flank topography Kein Zugriff M. Willecke, J. Brimmers, C. Brecher
3. Statistical study of the mesh load factor of planetary gear transmissions affected by inherent manufacturing errors Kein Zugriff J. Sanchez-Espiga, A. Diez-Ibarbia, M. Iglesias, A. Fernandez-del-Rincon, F. Viadero, J. Calvo-Irisarri, A. Fernandez-Sison
1. Vibration reduction of planetary gear drive using mesh phasing: modelling and experimental validation Kein Zugriff G. Devaraj
2. Influence of Axis Misalignments in Stepped Planetary Gear Stages on the Excitation Behavior – Test Rig Development and Simulative Analysis Kein Zugriff C. Westphal, J. Brimmers, C. Brecher
1. Review of different calculation approaches for the mean coefficient of friction in ISO 6336 Kein Zugriff N. Blech, C. Paschold, T. Lohner, T. Tobie, K. Stahl, L. Amar
2. Forward Performance-driven Design of Gear Parameters Kein Zugriff S. Chen, C. Liu, D. Qin
1. Scuffing load carrying capacity of high-speed gears with an isotropic superfinished surface Kein Zugriff J. Vorgerd, P. Tenberge, M. Steinrötter
2. On the Testing of Flank Fracture Calculations Based on 3D-Gears Kein Zugriff T. Tra My Truong, S. Schumann, B. Schlecht
3. White Etching Cracks (WECs) on gears of E-Axle applications Kein Zugriff T. Schmidt, B. Neubauer, D. Merk
1. Parametric system simulation of load sharing in planetary gearboxes Kein Zugriff J.-A. Meis
2. Mesh Load Factor in Multiple Planetary Stage Gearboxes Kein Zugriff A. Baseer, B. Bauer, C. Wang
3. Assessing gear mesh misalignment in a parallel gear set by transmission error measurements Kein Zugriff N. De Bie, W. Smet, T. Van Der Kamp
1. Review of the definition of the loads for spur and helical gears in standards and handbooks Kein Zugriff L. Amar
2. Hybrid models for the simulation of displacements and stresses in lightweight gears Kein Zugriff B. Guilbert, D. Dureisseix, P. Velex
3. Development of Damage-based Accelerated Life Test Code for Gearbox using Genetic Algorithm Kein Zugriff J.-H. Park, B.-S. Kim, D. Im, D.-J. Moon, J.-H. Kim, Y.-J. Park
1. Acoustical behavior of periodic flank modifications under dynamic operating conditions Kein Zugriff S. Sepp, A. Wenig, M. Otto, K. Stahl
2. The Influence of Wheel Body Design on Airborne Noise Kein Zugriff B. Abert, D. Werner
3. Impact of manufacturing deviations on the NVH behavior of modern gear design concepts Kein Zugriff U. Kissling
1. Design optimization of multi-stage gear trains with asymmetric teeth under a broad range of torques by incorporating multibody simulations Kein Zugriff D. Park, A. Rezayat, Y. Gwon
2. Comparing the contact characteristics of involute gear/ eccentric cycloidal gear calculated by various loaded tooth contact analysis models Kein Zugriff L.-C. Chang, Q. Y. Zhuang, S.-J. Tsai, J.-F. Hochrein, S. Landler, M. Otto, K. Stahl
3. Contact simulation of tooth flanks using Isogeometric Analysis Kein Zugriff C. Karampatzakis, A. Mihailidis, A. Mantzaflaris, C. Provatidis
1. Simulation Study on the Tribological Characteristics in the Meshing Contact in the Context of the Load Carrying Capacity Calculation of Internal Gears with Unbalanced Sliding Conditions Kein Zugriff M. Geitner, S. Preintner, T. Tobie, K. Stahl
2. Thermal model of a planetary gear set using an isothermal approach Kein Zugriff W. Ramdane, C. Changenet, S. S. Ouali, C. Chevrel-Fraux, P. Casanova
3. Wetting and oil flow analysis of planetary gearboxes using oil flow simulations Kein Zugriff C. Kunik, J. Kunert
1. Challenges and possibilities of virtual development of e-axle transmissions Kein Zugriff M. Reichl, P. Lenz, A. Oliva
2. Latest advancements in the lubrication simulations of geared systems: a technology ready for industrial applications Kein Zugriff F. Concli, M. N. Mastrone
3. Lubrication improvement at the HS-IS spline shaft interface of a wind turbine gearbox using the smooth particle hydrodynamic method Kein Zugriff M. Gebhardt, A. Rhode, B. Legrady
1. Design and analysis of compound stepped planetary gear drives for better transmission performances Kein Zugriff S.-J. Tsai, Q.-Y. Zhuang, L.-C. Chang
2. Evaluation of the effect of the rim thickness on the root stress cycle of helical planet gears with integrated rollers Kein Zugriff I. Gonzalez-Perez, A. Fuentes-Aznar, J. Calvo-Irisarri, N. Bilbao-Handley, X. Lopez-Fuentes, A. Fernandez-Sison
3. Experimental Investigation of Moving Contact Pattern in Helical Planetary Gearboxes Kein Zugriff M. Fürst, S. Sepp, D. Schweigert, M. Otto, K. Stahl
1. A comparison of time and frequency domain approaches for NVH Kein Zugriff J. Langhart, S. Ebrahimi, T. Kelichhaus
2. Investigation of Sound and Vibration Behavior of Cylindrical Gears Kein Zugriff A. Beinstingel, F. Haringer, W. Sigmund, M. Heider, B. Pinnekamp, S. Marburg
3. Validation of an industrial gearbox model for predicting vibro-acoustic behavior Kein Zugriff P. Chavan, M. Lutz
1. Helicopter Drive System Safety Dissertation Kein Zugriff S. Sartori, L. Alari, N. Motta, D. Podda
2. Smart Gearboxes for a Sustainable and Reliable Industry Kein Zugriff D. Meyering, C. Hussmann
3. Effect of Load Cycles on Return Loss and Resistance of Sensor and Antenna Circuits Printed on Plastic Gears Kein Zugriff T. Inoue, D. Iba, N. Fujita, A. Nishikawa, M. Ishii, J. Hu, H. Shimasaki, N. Miura, A. Masuda, I. Moriwaki, J. Hongu
1. Electromechanical Coupling Modeling and Torsional Vibration Analysis of Helicopter Electric Propulsion System Kein Zugriff H. Jia, D. Qin, G. Hu, X. Xu, W. Bai
2. Numerical analysis of bevel gear transmission acoustic emission using a 3D gear contact force model within a multibody system dynamics simulation environment Kein Zugriff M. Vivet, A. Rezayat, J. Verhoogen, K. Kucukcoskun, S. Donders
3. Experimental Investigation of Influence of Indexing Errors on Gear Rattling Kein Zugriff A. Donmez, A. Kahraman
1. Lubricant Free Transmissions for the food industry – A Comparison Kein Zugriff A. Wallinger, R. Vonderschmidt, S. Vonderschmidt
2. Analysis of Load Cycles and Local Wear of Dry and Solid-Lubricated Gears Kein Zugriff S. Sklenak, D. Mevissen, J. Brimmers, C. Brecher, B. Lenz, A. Mehner
3. Considerations on Lubrication of High-Speed Rotating Gear (First Report) Kein Zugriff K. Suzuki, K. Sakai, K. Sakai, T. Hara
1. Gear friction coefficient estimation using directional parameter under ATF lubricated condition Kein Zugriff J. Hongu, S. Hattori, J. Kato, T. Koide
2. Effect of LOL conditions under high velocity and high injection temperatures Kein Zugriff U. Cihak-Bayr, T. Wopelka, C. Wintersteiger
3. Influence of Surface and Material Technologies on Loss of Lubrication Performance of Gears Kein Zugriff B. Morhard, T. Lohner, K. Stahl
1. On the reduction of windage power losses in gears by the modification of tooth geometry Kein Zugriff M. Ruzek, R. Brun, F. Ville, P. Velex, Y. Marchesse
2. Efficient concepts for high ratio angular gearboxes Kein Zugriff M. J. Herberger, F. Rudolph, B. Sievers
3. Holistic Sustainability-Assessment of Gearboxes Kein Zugriff M. M. Klein
1. The relevance of pinion deflection and twisting for loaded tooth contact analysis of high reduction hypoid gears Kein Zugriff W. Wagner, S. Schumann, B. Schlecht
2. The effect of pinion axial positioning on noise and transmission error of face hobbed and face milled bevel gears Kein Zugriff L. Bonaiti, M. Brambilla, P. Chiariotti, A. Cigada, C. Gorla, G. Boni, P. Codeluppi
3. Exploration of trade-offs between NVH and efficiency in bevel gear design Kein Zugriff E. Grabovic, A. Artoni, M. Gabiccini, E. Ciulli
1. Transferability of the scuffing load capacity of gear oils determined on spur gears to hypoid gears Kein Zugriff A. Drechsel, J. Pellkofer, K. Stahl
2. Fatigue testing of large sized bevel gears Kein Zugriff E. Virtanen, M. Kanerva, G. Szanti
3. Calculation method for wear of steel-bronze rolling-sliding contacts relating to worm gears Kein Zugriff P. E. Schnetzer, J. Pellkofer, K. Stahl
1. Local load capacity analysis for the design of a balanced flank modification for cylindrical gears according to bevel gear procedures Kein Zugriff F. Mieth, D. Tazir
2. Analysis of new tooth profile design based on the biomimetics principles Kein Zugriff I. Atanasovska, D. Momcilovic
3. Analysis of the tip interference in low gear ratio internal spur gears with profile modification Kein Zugriff J. I. Pedrero, M. Pleguezuelos, M. B. Sánchez
1. Simulation-based optimization of gearing efficiency using thin coatings Kein Zugriff R. Beilicke, D. Bartel, L. Bobach
2. Gearbox efficiency of eDrives: correlation between measurement and calculation of load-dependent torque losses Kein Zugriff M. Yilmaz, M. Ayar, F. Zerulli, K. Humm, J. König, B. Schwarz
3. Effects of Surface Engineering on the Efficiency of Involute Helical Gears – An Experimental Investigation Kein Zugriff J. Zhang, B. Shaw, A. Hammer, I. Sewell
1. Digitalization of the Gear Development Process – Chances, Benefits and Risks Kein Zugriff J. König, M. Obermayr, T. Klein
2. Opportunities arising from digital twins in gear development Kein Zugriff C. van Oss, A. Hilbig, H. Sardemann, S. Schumann, B. Schlecht
1. Modelling and Analysis of the Effect of Root Modification on Load Sharing and Stress Values on Spur Gears Kein Zugriff A. I. Aydeniz
2. LUBGEAR – Experimental Campaign for Aviation Gears in Loss-of- Lubrication Kein Zugriff L. Braumann, H. Amri, V. S. Viteri, J. Ochoa
3. PVD Deposition of Nb-MoS2 Coatings on Gear Carburized Steel Kein Zugriff A. Carvalho, R. Rego, N. Fukumasu, D. Tamayo, F. Nascimento, I. Machado
4. Improvement of the transmission efficiency in electric vehicles by using double staggered helical gears with shortened teeth Kein Zugriff I. Gonzalez-Perez, A. Fuentes-Aznar
5. Analytical Method for Calculating the Nominal Tooth Root Stress in Worm Gear Shafts Kein Zugriff J. Gründer, A. Monz
6. Developing CAE solutions for Robotics gears: Cycloidal and Strain Wave Gear Drives Kein Zugriff O. Harris, C. Poyser, R. Patel, O. Shires
7. The effect of working surface deviation on transmission error in helical gears Kein Zugriff C. Dongu Im, W.-J. Chung, J.-H. Park, D.-J. Moon, Pfor. Y.-J. Park
8. A study on the efficiency prediction of a gear bearing drive by means of mathematical modelling Kein Zugriff A. F. İnceel, B. Özkan, B. Karba, M. Vardar
9. Backlash optimization via compatible gear couples on the assembly lines for planetary gearboxes Kein Zugriff B. Karba, N. Yildirim
10. Classifying plastic beveloid gear quality considering manufacturing errors Kein Zugriff A. Yavuz Kanyilmaz, B. Karba, M. VARDAR
11. Investigation of the electrical impedance of the gear mesh of helical gears in an industrial gearbox Kein Zugriff M. Hausmann, E. Kirchner
12. Development of Optimal Design Program for Macro-Geometry of Planetary Gear Set using Multi-Objective Optimization Algorithm Kein Zugriff B.-S. Kim, D. Im, J.-H. Park, W.-J. Chung, Y.-J. Park
13. A concept for comparison of new and aged lubricants in transmissions of electric vehicles and a method of oil aging on a test rig Kein Zugriff T. König, L. Cadau, L. Steidle, M. Kley, D. Cansu Güney, J. Albrecht, K. Weber
14. Parameter Based Definition of Eccentric Cycloid Gearings Kein Zugriff S. Landler, M. Trübswetter, M. Otto, K. Stahl
15. Model based NVH design: e-bike application Kein Zugriff H. Mahe
16. Effect of overlap ratio on gear dynamic behavior and noise level Kein Zugriff J. D. M. Marafona, J. H. O. Seabra, P. M. T. Marques, R. C. Martins
17. Influence of misalignment of large cylindrical gears on contact pattern in operation Kein Zugriff A. Miltenovic, M. Banic
18. Gear geometry, size and material influences not captured in ISO 6336 Kein Zugriff W. Smet
19. Cross-correlation analysis among tooth profile and helix deviations Kein Zugriff D. Yamazaki, D. Iba, J. Chong Low, I. Moriwaki
20. A Novel Dynamic Modeling Method of High-Speed Thin-Rimmed Gear Transmission Kein Zugriff J. Zheng, D. Qin, C. Liu
1. 1. Recycling of carbon fiber reinforced plastics – State of the Art and Challenges Kein Zugriff J. Woelling, F. Manis
  2. Advanced biopolymer compounds for technical applications Kein Zugriff K. Moser, S. Körber
2. 1. Prediction of tooth root fatigue failure of polymer gears for dry and oil lubricated contact and its comparison to experimentally obtained results Kein Zugriff S. Matkovič, D. Šeruga, M. Nagode, M. Kalin
  2. The effect of gear manufacturing quality on the mechanical and thermal state of a plastic gear Kein Zugriff D. Zorko, N. Vukašinović, B. Černe
  3. Improved Method for Validation of Root Stress in Polymer Gears Kein Zugriff D. Gallagher, E. Wiita, R. Weidig
3. 1. Prediction of Gear Fatigue Life Considering Glass Fiber Orientation Kein Zugriff K. Yanagisawa, K. Kamoshida, A. Domon
  2. Analytical tooth root stress calculation for short fiberreinforced plastic gears Kein Zugriff W. Kassem, J. Müller, M. Oehler, O. Koch
  3. Continuous prestressed reinforcement of plastic gear teeth and its effect on bending strength vs conventional reinforcement Kein Zugriff G. Vasileiou, C. Vakouftsis, C. Kalligeros, V. Spitas, C. Papalexis, A. Tsolakis, P. Zalimidis
4. 1. NVH performance of thermoplastic gears: modelling and measuring Kein Zugriff B. van Wissen, L. Pastukhov, F. Mitsuzuka, K. Iwanaga, A. Hasanovic
  2. Evaluation of the NVH Characteristics of Gear Drives with Plastic Gears by the Forced Response Analysis Kein Zugriff S. Ebrahimi, U. Kissling, C. S. Matkovič
  3. Optimization of the vibrational behavior of ZI crossed helical gears with a plastic wheel and a steel worm Kein Zugriff C. Kirchhoff, P. Tenberge
5. 1. Influence of the injection molding process on the tooth deflection of plastic gears during operation Kein Zugriff C. Herzog, D. Drummer
  2. Plastic Gears: Investigation on Noise and NVH Behavior Kein Zugriff J. Cathelin
  3. New generation in plastic gear technologies Kein Zugriff P. Michel
6. 1. A non-restrictive approach of gear geometry calculation for plastic gears Kein Zugriff F. Eigner, S. Oberle, M. Berger
  2. Applicability of classic analytical calculation approaches for the design of plastic gears Kein Zugriff M. Rothemund, M. Otto, K. Stahl
  3. Crossed helical gears – simulative studies and experimental results on non-involute geometries Kein Zugriff L. Becker, P. Tenberge
7. 1. Evaluation of specialty polymer performances in gear applications and the bias between modeling and testing approaches Kein Zugriff B. Devaux, C. Hamon, S. Montani
  2. Experimental Verification of High-Performance Polymer Gears in an Electric Vehicle Powertrain Kein Zugriff S. Reitschuster, T. Tobie, K. Stahl
  3. Influence of plastic-metal-pairings on the lifetime of gears Kein Zugriff S. Birk, E. Stoppel, V. Labriola
8. 1. Reduction of root and flank temperature using a hybrid polymer-metal rack Kein Zugriff C. M. C. G. Fernandes, J. M. A. Pinto, D. E. P. Gonçalves, A. R. Silva
  2. In-situ experimental methods for measuring tooth meshing displacements and wear during polymer gear tests using a high-speed camera with microscopy optics Kein Zugriff B. Černe, N. Vukašinović, D. Zorko
1. 1. Complete machining of complex transmission parts Kein Zugriff M. Brumm, D. Sari
  2. Advancing to The Next Level – Cost Efficient Roll-Inspection: Back from End-of-Line NVH to Skiving Process Kein Zugriff T. Kleiber, B. Neubauer
2. 1. Building a software toolchain for automated mass-customization of specific end-use gear unit parts using AM-driven design guidelines Kein Zugriff T. Jagiella, S. Haller, J. Lechner, T. Rung, M. Wöppermann, B. Zeeb
  2. Securing the Quality Chain by the Networking with the Gear Suppliers Kein Zugriff H. Yakaria
  3. Generation Method of Polygonal Shaped Work Pieces Based on Gear Meshing Theory Kein Zugriff D. Matsuura, D. Hashioka, T. Kobayashi, H. Maki
3. 1. Spur Gear Teeth Reconstruction via Direct Laser Deposition Kein Zugriff P. Romio
  2. Binder Jetting in Gears – Process Design and Tooth Bending Strength for Gears made of 17-4PH Kein Zugriff L. Klee, T. Bergs, M. Solf, J. Brimmers
  3. Indirect Selective Laser Sintering: Modeling and analysis of surface densification by shot peening Kein Zugriff I. Criscuolo, F. Carneiro, G. Guimarães, R. Rego, J. Mascheroni
4. 1. Estimation of brittleness of CCH-steel via measurement of micro-VH and simultaneous FWHM distribution Kein Zugriff A. Kubo, M. Nagae
  2. Investigation of the machinability of different quenched and tempered steels for the alternative process chain of planetary pinions in wind turbine gearboxes Kein Zugriff S. Hendricks, M. Solf, J. Brimmers, T. Bergs
  3. Investigating different nodular graphite irons for the application of gears – a step towards standardization by using reasonable quality criteria Kein Zugriff J. Lohmiller, F. Dobler, M. Wöppermann
5. 1. Gear Skiving with Minimum Twist Errors Kein Zugriff A. Hilligardt, V. Schulze
  2. The next level of axial forming for a sustainable component and process chain design Kein Zugriff N. Missal, S. Schwertel, M. Ludwig
  3. Enhancing gear performance through advanced mass finishing and DEM simulation Kein Zugriff F. Reinle, D. Mangherini, A. Bongiovanni
6. 1. Quality inspection of special geometries measured with computed tomography – Evaluation of involute cylindrical gears according to ISO 1328-1 Kein Zugriff K. Lübke, K. Stein
  2. Large gear metrology at PTB Kein Zugriff A. Wedmann, M. Stein, K. Kniel
  3. Optimization of product quality and manufacturing processes in real-time with vibration analysis Kein Zugriff S. Moschkau, S. Held
7. 1. Tooth Root Burnishing in the Kinematics of Gear Skiving Kein Zugriff P. Fischmann, A. Hilligardt, V. Schulze
  2. Surface integrity of 20MnCr5 pinion gears manufactured through laser powder bed fusion Kein Zugriff G. Guimarães, L. Robatto, R. Rego, A. Faria, A. Borille, J. Mascheroni
8. 1. The Magic Cutter – An economical solution for bevel and hypoid gear production based on the modular principle Kein Zugriff C. Braykoff, J. Thomas
  2. Application-oriented research on internal generating polishing Kein Zugriff N. Fujimura
  3. de Oliveira Löhrer Marker-Free, Single Item Traceability in Gear Wheel Production Based on Inherent Surface Patterns Kein Zugriff T. Schmid-Schirling, N. Saum, C. Eberz

International Conference on Gears 2023

Zusammenfassung

Schlagworte

Publikation durchsuchen

Bibliographische Angaben

Inhaltsverzeichnis

Ähnliche Veröffentlichungen